Course syllabus PVAP - Production Planning of Automotive Industry (ŠAVŠ - Sklad předmětů)

     Czech          English          

Course title: Production Planning of Automotive Industry
Semester: -- item not defined --
Course supervisor: Ing. David Staš, Ph.D.
Supervising department: Department of Production, Logistics and Quality Management (ŠAVŠ)
Prerequisites for registration: Organization and Management of Production or Bachelor state examination
Time allowance: full-time, 0/2 (hours of lectures per week / hours of seminars per week)
part-time, 0/8 (lectures per period / seminars per period)
Type of study: usual
Form of teaching: seminar
Mode of completion and credits: Classified fulfillment of requirements (3 credits)
Course objective:
Learning outcomes of the course unit The aim of the course is to help students acquire knowledge and acquire skills in the field of automobile production planning, which will support the management of the planning process at the level of designers and specialist specialists. From a knowledge point of view, students will become familiar with the production of cars and components, with the main principles, methods and tools applied in the process of production planning.
In terms of skills, the main focus is on acquiring methods and tools suitable for preparation of new products, process changes and optimization.
 
Course methods: - Lectures
- Excursion
- Best practices
 
Course content:
1.Introduction to production planning (allowance 0/2)
 
a.- familiarization with the structure of Production Planning, description and structure of the planning process, vehicle life cycle, PEP, range of work and location

2.Digital factory and simulation of material flows (allowance 0/2)
 
a.- application of tools, SW and simulation methods in the process of virtualisation of technological units, detection of bottlenecks in the production stream, simulation of ergonomic loads and their elimination

3.Press shop (allowance 0/2)
 
a.- simulation of the pressing process and compressibility, a set of used technologies in Škoda Auto, examples from practice

4.Welding shop (allowance 0/2)
 
a.- welding body composition, welding methods and materials used, application of welding technology to welding lines, introduction to robotics

5.Paint shop (allowance 0/2)
 
a.- description of the painting process in relation to the car, design, planning and implementation of the paint shop technology, corrosion protection of the bodywork

6.Assembly (allowance 0/2)
 
a.- Structure of the main line in ŠKODA AUTO a.s., JIT, JIS, used conveyor technology, product care and changes

7.Production of components and gearboxes (allowance 0/2)
 
a.- content and types of plant to produce components, specific component planning tasks

8.Buildings and infrastructure (allowance 0/2)
 
a.- construction planning support, legislative process of construction, term sequence and volume of work due to the start of new products

9.Ecology and health protection (allowance 0/2)
 
a.- environmental policy of Škoda Auto, planning and realization of environmental care, employee health protection ŠKODA AUTO a.s.

10.Industry 4.0 (allowance 0/2)
 
a.- definition of industry 4.0, introduction of industry principles 4.0 to production, cooperation with TESTBED, connection to the canning board

11.Excursions to the workshop, the welding shop and the paint shop (allowance 0/2)
12.Excursion of operations production of components, production of gearboxes and assembly line (allowance 0/2)
 
Learning outcomes and competences:
After completing the course, student:
 
-Will discuss basic problems of planning in automotive
-Will express the essence of production planning in the automotive
-Will identifies basic key factors affecting planning processes

Teaching methods and workload (hours of workload):
Type of teaching methodDaily attendanceCombined form
Direct teaching
     Attendance of lectures24 h0 h
Self-study
     Course reading and ongoing preparation14 h0 h
     Ongoing evaluation18 h0 h
     Preparation for final test28 h0 h
Total84 h0 h
 
Assessment methods:
Requirement typeDaily attendanceCombined form
Active lecture/seminar/workshop/tutorial participation30 %0 %
Mid-term test(s)20 %0 %
Final test50 %0 %
Total100 %0 %
 
Course completion:
1. A prerequisite is participation in exercises and at least one excursion.
2. Point evaluation of the subject:
a. Maximum 30 points for attendance at the exercises, max. 20 points for partial tests. It is necessary to get at least 31 points to proceed to the final test.
b. A maximum of 50 points for the final written test, questions from discussed topics and excursions.
 
Support for combined/distance forms of study:
There will be available at IS ŠAVŠ document server:
- Lectures (for presentation form of study) in the form of presentations.
 
Reading list:
Basic:
Language of instruction: Czech
TOMEK, G. -- VÁVROVÁ, V. Integrované řízení výroby.: Od operativního řízení výroby k dodavatelskému řetězci. Praha: GRADA, 2014. ISBN 978-80-247-4486-5.

Recommended:
Language of instruction: Czech
VALSA, O. -- KEŘKOVSKÝ, M. Moderní přístupy k řízení výroby: 3. Doplněné vydání. Praha: C. H. Beck, 2012. 176 p. ISBN 978-80-7179-319-9.

Study plans:
-- item not defined --
 
Run in the period of: WS 2019/2020, SS 2018/2019, WS 2018/2019, SS 2017/2018, WS 2017/2018   (and older)
Course tutor: Ing. David Staš, Ph.D. (supervisor)
Teaching language: Czech
Room: Mladá Boleslav


Last modification made by Ing. Aleš Kutín on 09/02/2019.

Type of output: